DALI Products

Functions
After powering-up the device an internal test sequence is initiated that lasts for no more than two seconds. The device then acts in normal mode and awaits DALI commands. The "STATUS" LED indicator is lit when the DALI BUS is correctly supplied. LED indicators one to four show the current status of each relay: a lit LED means the corresponding relay is switched on, an unlit LED means the corresponding relay is switched off.

Test mode

• Test mode can be activated at any time by pressing the push button "TEST"
• A short push of the button, for a period less than three seconds, changes which relay is selected, indicated by the corresponding LED indicator blinking
• By pressing the push button for a period of more than three seconds the selected relay is switched on/off, indicated by the way in which the LED indicator blinks (predominantly on means the relay is switched on, predominantly off means the relay is switched off)
• The device will return to normal mode after five seconds of push button inactivity

Technical data
Key features

• Four independent relay contacts
• 12 A maximum switching current per contact
• Push button for manual control (test function)
• One DALI address for each contact (DALI device type 7, EN 62386-208)

Physical connections

• Mains cable wires: AWG 24 - 12 (0.2 - 2.5 mm²)
• DALI cable wires: AWG 28 - 16 (0.08 - 1.5 mm²)
• Relays cable wires: AWG 24 - 12 (0.2 - 2.5 mm²)

Construction

• Housing: 4U DIN rail box, 71 mm wide
• Weight: 300 g
• IP rating: IP 20

Certification

• EN 55015 Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment
• EN 61547 Equipment for general lighting purposes EMC immunity requirements
• EN 60950-1 I Information technology equipment - Safety - Part 1: General requirements
• EN 62386-208 Digital addressable lighting interface

Environmental conditions

• Operating temperature range from 0 ºC up to 40 ºC
• Relative humidity 85 % max., non-condensing
• Storage temperature range from -40 °C up to 70 °C

Power

• Mains supply: 220 - 240 VAC / 50 - 60 Hz
• Max. system power: 6 W
• DALI consumption < 2 mA
• Relay loads: 12 A (per contact)
• Insulation: 4 kV

Technical data
Key features

• Manual or fully automatic control of light
• DALI type 8 support - up to 192 DALI type 8 devices
• Possibility of connecting up to 81 TW luminaires or 64 RGB luminaires
• Three independent DALI lines - one internally powered, two externally powered
• User configurable time scheduler
• Possibility of connection light level and movement sensor
• Energy saving solution
• Daylight simulation - bringing natural conditions into interior
• Security option - password protection of settings
• Two modes: RGB and dynamic white
• Simple and fast setting of colour with TW or RGB
• User friendly graphic interface
• User pre-settable screen savers
• Static scene pre-sets
• Dynamic scene pre-sets

Display

• Size: 7″
• LCD Type TFT, transmissive, anti-glare
• Resolution: 800 x 480, 262 K colors
• Viewing angle (H / V): 140 / 120 deg
• Luminance: 350 Cd / m2
• Contrast ratio: 350:1
• Touchscreen capacitive
• Temperature range 0 °C to 40 °C

System Hardware

• CPU Texas Instruments AM3354, 720 MHz
• Memory: 256 MB SDRAM
• Flash: 128 MB NAND FLASH
• Networking LAN 100BaseTX, Bluetooth, Wi-Fi
• I/O 3 x DALI (1 x DALI internally powered - 250 mA)

General

• Power consumption: max. 9 W
• Power input: 12 VDC
• Cooling system fanless
• Temperature range 0 °C to 40 °C

Downloads & Support

• DALI TouchME 7 userguide.pdf (1 MB)

Technical data
Power

• Input voltage: 12 VDC
• System power < 0.5 W
• DALI consumption < 2 mA
• Insulation: class II

Physical connections

• Power cable wires: AWG 28 - 16 (0.08 - 1.5 mm²)
• DALI cable wires: AWG 28 - 16 (0.08 - 1.5 mm²)
• Ethernet cable: UTP CAT5E

Construction

• Housing: 2U sized DIN-box
• Weight: 70 g
• Dimensions: 94 x 36 x 60 mm

Certification

• EN 61347-1 Lamp control gear - Part 1: General and safety requirements
• EN 62386-102 Digital addressable lighting interface, general requirements for control gears
• EN 61347-2-1 Lamp control gear - Part 2-11: Particular requirements for miscellaneous electronic circuits used with luminaires

Environmental conditions

• Operating temperature range from 0 ºC up to 40 ºC
• Relative humidity 85 % max., non-condensing
• Storage temperature range from -40 °C up to 70 °C

Functions
Switch2 DALI 4 detects short-circuit connection between wires input 1 - 4 and COM. Module is designed to be used with standard push buttons - short-circuit connection is the active state. The logic of the module differentiates between short and long press of the push buttons. Short press is detected when the short-circuit detection lasts shorter than one second. If the short-circuit connection lasts longer it is detected as long press. User can configure different reaction to short and long press.
Each input of Switch2 DALI 4 can be configured with different DALI address (device support broadcast, group addresses and short addresses). Three types of reactions can be configured for each input: Static-Commands, Direct-Level or Toggle. In Static commands mode device transmit defined command each time a press is detected. The most useful commands are: MIN_LEVEL, MAX_LEVEL, UP or DOWN. If desirable user can set up any command listed in DALI standard (IEC 62386-102). In Direct level mode device transmit defined brightness level each time a press is detected (for example 50 %). In Toggle mode device toggles between two commands each time a press is detected. The user can choose from three toggle functions: MIN / MAX, ON / OFF and Scene X / Scene Y. Scene X and Scene Y are settable number of DALI scenes which are toggled. The configuration can be changed using special programmer (on demand).
For the reaction on long press it is possible to set whether the command should be sent only once or it should be repeated (for example UP / DOWN commands). The period of repetition is also settable (one second period). Switch2 DALI 4 is delivered with default configuration. It is a DALI powered device therefore external DALI power supply has to be connected on the DALI line.

Technical data
Key features

• Powered from DALI BUS, compatible with standard DALI rating
• Up to four user inputs
• Default functions - ready to use out-of-box
• Small dimensions (L x W x H): 27 x 20 x 4 mm
• DALI consumption < 9 mA

Control Inputs

• Voltage range open: 5 VDC / closed: max. 0.3 VDC
• Current range: max. 1 mA

Physical connections

• Mains cable wires: AWG 24 (0.5 mm²)
• DALI cable wires: AWG 24 (0.5 mm²)

Certification

• EN 55015 Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment
• EN 61547 Equipment for general lighting purposes EMC immunity requirements
• EN 62386-102 Digital addressable lighting interface, general requirements for control gears

Environmental conditions

• Operating temperature range from 0 ºC up to 40 ºC
• Relative humidity 85 % max., non-condensing
• Storage temperature range from -40 °C up to 70 °C

Construction

• Housing encapsulated PCB
• Weight: 10 g

Functions
The DALI envSens measures illuminance and correlated colour temperature (CCT) properties within its scanning area - illuminance in lux and CCT in Kelvins. Measurement occurs automatically using automatic range switching within an illuminance range of 100 - 30000 lx and CCT range of 2500 - 8000 K. The sensor communicates using the industry standard DALI protocol once addressed and set using any standard DALI configuration tool. Additional sensor parameters can be set using a USB / DALI bridge and related software tool. By default, the sensor functions in passive mode with regulation disabled and where measured values can only be read.
The basic parameters required for regulation are desired illuminance and CCT values and connection to type-defined and controllable Tunable-White luminaires. The sensor can be used to regulate warm/cold two-channel luminaires, brightness / CCT two-channel luminaires and DALI type 8 luminaires. It is possible to assign each channel its own address, for example, a cold channel, warm channel, brightness channel, CCT channel or DALI type 8 channel. All connected Tunable-White luminaires can be controlled in parallel using illuminance only regulation, CCT only regulation or dual regulation.

Technical data
Key features

• Passive/Active mode - offers direct regulation of Tunable-White luminaires
• Configuration via DALI BUS
• Installation into ceiling
• Biasing from the DALI BUS with an input voltage range compatible with the DALI standard
• Illuminance and CCT measurement

Power

• Voltage at DALI input: 12 - 25 VDC
• Input current < 9 mA

Connections

• Cable wires: AWG 24 (0.5 mm²

Environmental conditions

• Temperature range from 0 ºC to 40 ºC
• Relative humidity 85 %, no condensation
• Storage temperature range from -40 °C to 70 °C

Construction

• IP rating: IP 40
• Weight: 200 g
• Dimensions Ø: 115 x 40 mm
• Opening Ø: 105 mm

Functions
The DALI TW module is a DALI device designed for Tunable-White control. It is not a power source for LEDs. For correct function an external LED driver must be used (constant current). Selection of the LED driver depends on the LED load used (forward voltage and current). DALI TW module controls the CCT of light according to the DALI commands received. On DALI line, the device appears as standard DALI device type 6 or device type 8 (LED driver) allowing for direct CCT level control, group addressing, fading and scene settings. The DALI TW module represents simple way of CCT control via DALI using standard components - LED driver and DALI controller.

Technical data
Key features

• Independent control of CCT
• Up to 180 V voltage range
• DALI control (device type 6)
• DALI control (type 8) - one adress only

Physical connections

• Mains cable wires: AWG 28 - 16 (0.08 - 1.5 mm²)
• DALI cable wires: AWG 28 - 16 (0.08 - 1.5 mm²)
• LED cable wires: AWG 28 - 16 (0.08 - 1.5 mm²)

Power

• Mains supply: 90 - 260 V/AC / 47 - 400 Hz / 120 - 370 V/DC
• System power < 200 mW, DALI consumption < 2 mA
• Insulation: class II

Output

• Output voltage range: 30 - 180 V/DC
• Output current range: 0 - 2 A
• Output power range: 0 - 150 W

Environmental conditions

• Operating temperature range from 0 ºC up to 55 ºC
• Relative humidity 85 % max., non-condensing
• Storage temperature range from -40 °C up to 70 °C

Construction

• Housing: "Open-Frame"
• Weight: 60 g
• Dimensions: 94 x 45 x 26 mm

Certification

• EN 61547 Equipment for general lighting purposes EMC immunity requirements
• EN 62386-102 Digital addressable lighting interface, general requirements for control gears
• EN 55015 Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment

Downloads & Support

• DALI TW 8 datasheet.pdf (209 KB)